Concrete Resurfacing in Arlington, Texas
Concrete Resurfacing in Arlington, Texas
Arlington filled in between two downtowns across four decades, and most of its driveways date from that build out. Resin Rock resin bound resurfaces the sound ones instead of sending them to a landfill.
Arlington housing stock tells you when each part of the city grew. North Arlington around Randol Mill and Interlochen went up in the 1960s and 1970s. The middle of the city filled in through the 1980s, and south Arlington toward the Mansfield line kept building into the 1990s. That means a huge number of driveways, patios and pool decks that are somewhere between thirty and sixty years old, poured to the standard of their day and now well past their intended service life.
Most of those slabs are worth keeping. Resin bound is natural stone aggregate blended into a clear UV stable binder and hand troweled over prepared concrete, so a sound driveway becomes the base for a seamless permeable surface instead of becoming a dumpster load. There is no loose stone, no control joint to step and nothing to reseal every couple of years. On a rental or a house you plan to sell, it is also the cheapest way to change what the front of the property says about it.
Resin Rock supplies the binder, the aggregate and the training behind the approved installers working this stretch of Tarrant County. Jobs run from Interlochen and Rush Creek driveways to Dalworthington Gardens patios, Viridian pool decks and small commercial entries around the entertainment district. Material ships from the Texas distribution point, backed by the Sarasota headquarters, so the blend a homeowner picks is one the installer can actually order for the date.
Resin bound in Arlington at a glance
- Laid over your existing concrete, no demolition
- Fully permeable, so rain drains through instead of ponding
- Seamless finish, no loose stone and no weeds in joints
- UV stable binder holds color in direct sun
- Slip resistant when wet, which matters on steps and pool decks
- Installed by Resin Rock approved installers serving Arlington, TX
Why Arlington concrete is all wearing out at once
Age plus clay is the short version. The ground under Arlington sits on the transition between the shale and marl of the Fort Worth side and the deeper prairie clay to the east, and either way it changes volume with moisture. A slab poured in 1978 has been lifted and dropped every year since, and by now the joints have opened, one panel is proud of the next and the crack at the apron has been filled twice. Concrete does not get better with more patching.
Weather does the rest. Arlington sits in the middle of a hail corridor, and spring storms bring both the hail and the hard rain behind it. Summer slab temperatures cook anything applied to the surface, and a cold front dropping thirty degrees overnight finishes it. Coatings that were sprayed on to smarten up an aging drive go brittle, then let go along the edges. Meanwhile rental turnover in parts of the city means surfaces get pressure washed hard and often, which polishes them slick.
Forty year old flatwork
A great deal of Arlington concrete was poured between the 1960s and the 1990s to the budget of its day. It has outlived its design life and is failing at joints and corners.
Hail season budget cycles
Spring storms bring roof claims, and once scaffolding and crews are on a property the tired driveway underneath finally gets addressed. Hail rarely damages the drive itself.
Aggressive pressure washing
Frequent cleaning on rentals and turnover properties burnishes a broom finish smooth over time. It looks clean and then behaves badly on the first wet morning of the season.
What resin bound resurfacing actually is
Resin bound is a mixed-on-site surface. Aggregate and a two part UV stable resin go into a forced action mixer at an exact ratio, and the resulting blend is troweled over your existing concrete at depth. It cures into a single seamless, porous sheet.
People confuse it with resin bonded, and the two behave nothing alike. Bonded work scatters dry stone onto a resin coat, so the surface is textured, sheds loose grit and holds water on top. Bound work carries the resin all the way around every stone, which is what makes it flat, fixed and free draining.
The practical result in Arlington is that you keep your slab, lose the cracked and stained surface on top of it, and gain something that handles rain by absorbing it rather than pushing it toward your foundation.
Why it works over existing concrete
- Bridges and hides surface cracking and spalling
- Bonds to a properly prepped, structurally sound slab
- Adds roughly three quarters of an inch, so thresholds and garage doors usually still clear
- Works around existing drains, channels and pool coping
- Rated to hold up to 40,000 lbs when correctly installed
- Available in 30+ aggregate blends including Glow Rock
- No demolition, no dumpster, no re-pour, no 28 day concrete cure
What Arlington homeowners resurface
Driveways and parking aprons
The bread and butter job here. Resin bound carries up to 40,000 lbs at driveway depth and goes down as one continuous run, so there are no joints for weeds and fire ants to work into and no oil stained control lines across the front of the house.
Pool decks from the 1970s and 1980s
Arlington has a generation of backyard pools with decks finished in spray texture that has long since chalked. Resin bound covers it once the old coating is ground off, grips when wet and drains rather than holding water at the coping through a wet spring.
Patios and rental turnover work
Between tenancies a worn back patio is the cheapest thing to fix that guests and applicants actually notice. A troweled stone surface goes down in a day on a typical patio and needs no reseal cycle, which suits a landlord who does not want a recurring maintenance line.
Commercial entries near the stadiums
Bars, restaurants and small venues around the entertainment district need entries that stay safe underfoot on an event night. Prep aside, most doorways are a one day install, so a business can stay open through the work rather than closing on a weekend.
Browse completed Resin Rock projects or drag the visualizer slider to see plain concrete become a resin bound surface.
Concrete resurfacing cost in Arlington
Arlington quotes are usually decided by slab condition rather than by anything exotic. A sound drive needing grinding, crack treatment and priming sits at the low end of the range. A drive with a stepped apron or a rocking panel needs that section repaired or replaced first, and it is separate work. Old spray texture on a pool deck has to be ground off completely, which is real labor. Access on most of these streets is straightforward, which helps the number.
| Option | Typical installed range | What you actually get |
|---|---|---|
| Resin bound over sound concrete | $12 to $25 per sq ft | Permeable, seamless, UV stable, no joints to step, 15+ years on a sound base |
| Tear out and re-pour | $10 to $18 per sq ft plus demo | The default quote on an old drive. Demolition, hauling, a cure period, then plain concrete again |
| Spray texture or acrylic overlay | $6 to $14 per sq ft | Common on older Arlington pool decks. Chalks, lifts at the edges and lets cracks come back through |
| Stamped concrete | $12 to $22 per sq ft | A new pour with joints and a reseal cycle. Not permeable and it still steps where the clay moves |
| Paver overlay | $18 to $35 per sq ft | Good looking but jointed. Sand washes out in hard spring rain and edges settle over a few seasons |
These are typical installed planning ranges for budgeting only, never quotes. Coating removal, slab repair, apron condition and blend choice all change the real figure on an Arlington property.
Get a real number for your slab
Square footage, slab condition, access, drainage and aggregate choice all move the price. Send the details and an approved installer will price the actual job.
How a resin bound resurfacing job runs in Arlington
Most residential driveways and pool decks are done in one to two days once the base is ready. Here is the sequence an approved Resin Rock installer follows.
Survey and base check
An approved installer checks whether your existing slab is sound enough to build on. Sound concrete is a huge cost saver because it becomes the base instead of landfill.
Prep and clean
Grinding, pressure washing, degreasing and crack treatment. Oil spots and old sealers have to go or the resin will not bond properly.
Edging and detailing
Resin Trims edge profiles, channel drains and thresholds are set to the finished height so the surface finishes flush and clean.
Primer
A primer coat seals the slab and locks the resin bound layer to the concrete underneath. Skipping this is one of the fastest ways to get delamination.
Forced action mixing
Aggregate and Part A/Part B binder go into a forced action mixer at exact ratios. A drum mixer will not do this job. Consistency here is what makes the finish uniform.
Hand trowel
The mix is poured and troweled to depth, usually 15 to 18mm on foot traffic and up to 24mm on driveways. Crews can lay up to 1,500 sq ft in a day.
Cure and hand over
Foot traffic typically within 6 to 8 hours and vehicles usually after 24 to 48 hours depending on temperature and humidity. No loose stone to sweep up afterwards.
The part that decides whether it lasts
The number one cause of resin bound failure is not the resin. It is a weak or poorly compacted base. Any installer who wants to skip the prep and start mixing on day one is telling you something. Ask what they found when they surveyed your slab and what they plan to do about it.
Color and aggregate choices
Blend choice does more work than people expect. Resin Rock screens over 30 aggregate blends so every bag matches the last, which is the only reason a surface laid across two days looks like one surface. Quartz reads bright and uniform. Granite is the safe, natural looking default. Marble is the light, soft option. Basalt is the dark, contemporary one.
Two practical rules. Light blends run cooler in the sun and show dirt less than people fear, because the surface is textured rather than flat. Dark blends hide tire marks and oil drips on a driveway but get hot. If the surface is walked barefoot, go lighter. If it is parked on, go mid to dark.
For feature work, Glow Rock from Glow Surfaces charges in daylight and glows softly after dark. It works as a path edge, a pool surround border or a driveway inlay rather than a whole surface.
Questions worth asking your Arlington installer
- Is my slab sound enough to overlay, and how did you check?
- Are you using UV stable resin on the sun exposed areas?
- What depth are you laying, and does it suit vehicle load?
- How are the edges finished and with which trim profile?
- Where does the water go once it drains through?
- Are you a Resin Rock approved installer, and at which tier?
Areas we cover around Arlington
Arlington sits between two metro centers and is supplied from the Resin Rock Texas distribution point, backed by the Sarasota headquarters. That in state supply is why a crew running jobs across Tarrant County can order the blend a customer chose rather than substituting whatever is on hand. Blends are batch tested and named, so if you are doing a driveway now and a pool deck next spring, note the blend on your paperwork and the second job can be ordered to match.
For homeowners and landlords, start at the Find an Installer directory. Approved and Expert tier installers have completed Resin Rock training and can show they know how to assess an aging slab, remove a failed deck coating and finish an edge that stays sharp against a lawn. Because Arlington sits between the Dallas and Fort Worth networks, coverage here is usually good. If no crew shows up near your zip code, send the project through the estimate form and we will point you at one.
Find an approved installer or check our distribution locations.
Maintenance and lifespan
A correctly installed resin bound surface should give you fifteen years or more. The maintenance is genuinely light. Sweep or blow off leaf litter so the pores stay open, and give it a jet wash once or twice a year on a wide fan tip held back from the surface.
Spills come off with warm water and a soft brush. Do not use a stiff wire brush, harsh solvents or a turbo nozzle held close, because all three can chip the resin skin off the top of the stone. Weeds do not grow up through it, but windblown seed can occasionally root in surface debris, which is another reason to keep it swept.
If a section ever does get damaged, resin bound is repairable. An approved installer can cut out and relay a patch in the same blend rather than replacing the whole surface.
| Task | How often | Notes |
|---|---|---|
| Sweep or blow off debris | Monthly | Keeps the pores draining freely |
| Jet wash | 1-2 times a year | Wide fan tip, 12 inches back, never a turbo nozzle |
| Spot clean spills | As needed | Warm water and a soft brush, no solvents |
| Check edges and trims | Yearly | Look for lifted trim or a soft edge and call it in early |
| Professional inspection | Every few years | Approved installers patch repair in the original blend |
Why Arlington projects specify Resin Rock
We formulate, we do not relabel
Our binder is developed with trusted formulators rather than rebadged from whatever generic drum is cheapest that quarter. Part A and Part B, UV stable for sun exposed work, non UV for shade and vertical.
Batch tested aggregate
Quartz, granite, marble and basalt screened so each bag matches the last in size, shape and color. That is why a driveway laid on Friday matches the section laid on Monday.
Seven distribution points
We ship from seven locations nationwide so material is not sitting on a truck for a week. See our locations.
Two industry awards
Resin Rock has been recognized twice by the industry, and binder formulas are tested on an ongoing basis rather than resting on one certificate from years ago.
A certified installer network
Approved installers have proven they can prep a base, hit the mix ratio and finish a surface to warranty standard. Find one near you.
Whole system under one roof
Binder, aggregate, kits, Resin Trims edging and Baron mixers. One supplier, one point of accountability.
Arlington concrete resurfacing questions
My driveway is from the 1970s. Is it too far gone to resurface?
Age on its own is not the test, condition is. Plenty of Arlington drives that look terrible are structurally fine underneath, and crazing, surface wear, staining, old patches and hairline cracking are all perfectly good candidates for an overlay. What rules it out is a panel that rocks when you walk on it, a section that has dropped away from the garage apron, a crack with a real vertical step across it, or water standing on it a day after rain. An approved installer will walk it and tell you which category you are in.
We are using hail money on the exterior. Where does the drive fit?
Do the roof and any elevation work first, then the flatwork. Hail almost never damages a driveway itself, since roofs, vehicles, screens and skylights take the impact, so the drive is not usually part of the claim. What the claim does is bring exterior budget and crews to the property, which is a practical moment to deal with a slab you have been ignoring. Just sequence it so nobody is dropping shingle bundles or debris onto a fresh surface, and tell your installer what else is booked.
This is a rental. Will it survive tenants?
It stands up well. The wearing surface is natural stone in a resin matrix rather than a film sitting on top of the slab, so it does not scuff or peel the way a coating does, and there are no joints for grit, weeds or ants to get into. It carries vehicle loads at driveway build up and is rated for 15+ years with a sound sub base. Maintenance is blowing debris off and an occasional rinse, with no reseal cycle to budget for, which is usually the deciding point for an owner running several properties.
Our pool deck still has its old spray texture. Does that have to come off?
Not over it. The old coating has to be ground off completely first, because resin bonds to sound concrete and not to a texture layer that is already chalking and releasing. On a 1980s Arlington deck that removal is a real line item with real dust control, and any bid that goes straight to laying material should make you suspicious. Once the coating is gone and the deck underneath is clean and sound, it makes an excellent base, and you keep the slab instead of paying to demolish and replace it.
Do I need a permit or HOA approval in Arlington?
Check before you book, because it depends where you are. The City of Arlington runs its own process, and Pantego and Dalworthington Gardens are separate towns with their own rules even though they sit inside the same map. Newer communities such as Viridian have design review that covers street facing surfaces. Resurfacing is generally a simpler case than a new pour because the structure and footprint do not change, but confirm with your city and your HOA, and ask your installer for product data to include in the submission.
How quickly can a job be done around an event weekend?
For a home it rarely matters, but for a business near the stadiums it decides everything. Most entries and small patios are a one day install once the base is ready, and a trained crew can lay up to 1,500 sq ft in a day. Prep usually happens the day before. Foot traffic typically returns within hours rather than days, which is the practical difference from a re-pour. Book against the calendar, tell your installer the event dates, and plan prep for the quiet part of the week.
More Resin Rock coverage
Texas
Nearby metros
Nationwide
Get a free estimate in Arlington
Send the square footage, say whether there is an old coating on the slab and add photos of the apron and the worst joints. A Resin Rock approved installer will assess the concrete you actually have, tell you what has to be repaired first and price the whole job rather than a rate per foot. Estimates are free and there is no obligation.
Or call (941) 415-0273. Contractor rather than homeowner? See installer training.